Electrovoice EV ZX5 - 15 inch 2 way speaker system
Key Features - EV ZX5-90B
• DVX3150 15 inch LF Transducer with Forced Air Cooling
• ND2 2 inch Voice Coil, 1 inch Exit Neodymium Compression Driver
• 90 degrees x 50 degrees Coverage Pattern
• 600W Continuous (2400W) Power Handling
• High Sensitivity, 132 dB Maximum SPL
• Adjustable Monitor Angle (45 degrees or 55 degrees)
• 3 Anchor Plates for Single Stud Fittings and
10 Integral Suspension Points
• Available in Black or White
• Full Line of Accessories
The Electro-Voice Zx5 is the new standard of no compromise audio
performance and versatility in a simple to use, compact package.
At its heart are the transducers. First is the DVX3150 high
performance low frequency transducer. EV used advanced
computer aided design techniques to create forced air, directional
voice coil cooling for high power and efficiency. Finite element
analysis was used to optimize the suspension and magnetic structure
for long, linear travel to provide low distortion and greater LF
extension. These features and details, such as forged magnetic
components and special materials, provide reliability with a 500W
power rating in a lightweight transducer. Next is the ND2, a 2-inch
voice coil compression driver based on neodymium motor structure
to allow for maximum output while reducing size and weight to a
minimum. Its precision phasing plug and titanium diaphragm provide
better HF performance, while the integral heatsink provides cooling
for high power output.
The high tech enclosure uses injection-moulded high-impact
polypropylene structural foam to make the Zx5 incredibly durable.
The enclosure geometry elements have been carefully designed to
provide maximum rigidity and bass response. By design the Zx5 is
also a perfect solution for stage monitors by allowing two angles
(45 degrees or 55 degrees without any additional accessories.
Two coverage patterns are available; 60 degrees x 60 degrees coverage for long throw
and cluster applications, 90 degrees x 50 degrees coverage for wider coverage
or shorter distances.
The Zx5 is equipped with three anchor plates for rigging with single
stud-fittings, along with two more possible anchor plate attachment
points on the bottom. For permanent suspension or attaching
brackets, the Zx5 also has two M8 inserts on the top and bottom,
two under the handle, and four on the back of the enclosure, for a
total of 10. All versions are available in black or white.
Specification – Electrovoice ZX5 90B
Freq. Response1(-3 dB) : 58 Hz - 18 kHz
Freq. Range1(-10 dB) : 39 Hz - 20 kHz
Rec. High pass Frequency : 36 Hz
Axial Sensitivity : 98 dB (1W/1m)
Max Calculated SPL : 132 dB
Horizontal Coverage : 90 degrees
Vertical Coverage : 50 degrees
Rated System Power : 600W Continuous, 2400W Peak
LF Power Handling : 500W Continuous, 2000W Peak
HF Power Handling : 40W Continuous, 160W Peak
LF Transducer : DVX3150, 15 inch (300mm) Driver
HF Transducer : ND2, 1 inch (50.8mm) exit Neodymium
Compression Driver
Crossover Frequency : 1.5 kHz
Nominal Impedance : 8 Ohms
Minimum Impedance : 6.5 Ohms
Connectors : Neutrik Speakon NL4
Enclosure Material : Polypropylene Structural Foam
Suspension : Enclosure has locations for 5 Single Stud
Attachment Plates and 10 Forged
Steel Eyebolts - 2 on Top, 2 on Bottom,
2 on Side, and 4 on Rear of Enclosure
Grille : Polyester Powder Coated, 16GA
Galvanized Steel
Environmental Spec : IEC 529 IP24 / IP44 (PI Version)
Dim (H x W x D) : 692mm x 446mm x 411mm
Net Weight : 22.2 kg
Shipping Weight : 26.0 kg
|
